How to reset BFT remote control

The BFT remote control is a useful device for opening and closing automatic doors and gates. However, it may happen that the remote control stops working properly or needs to be reset to synchronize it again with the opening system. In this article, we will explain how to reset the BFT remote control simply and quickly.

Battery Check

Before proceeding with the reset of the BFT remote control, it is important to check the status of the batteries. Low or depleted batteries could cause problems with the functioning of the remote control and prevent the success of the reset procedure.

How to check battery status

To check the status of your BFT remote control's batteries, follow these simple steps:

• Open the battery compartment on the back of the remote control
• Remove the old batteries and replace them with new AAA alkaline batteries
• Close the battery compartment and turn on the remote control

After replacing the batteries, check if your remote control works properly. If it does not turn on or continues to have problems, it may be necessary to contact a specialized technician for further checks.

Remember that battery life depends on how often you use your remote control. If you notice that batteries are running out frequently, it may be necessary to replace your remote control.

With proper maintenance and periodic replacement of batteries, you can ensure optimal functioning of your BFT remote control.

Remote Control Reset Procedure

If your BFT remote control is not working properly, the reset procedure may solve the problem. Follow these steps:

1. Press and hold the "A" and "B" buttons simultaneously for about 3 seconds.
2. After 3 seconds, the LED on the remote control will blink slowly.
3. Release both buttons and wait for the LED to turn off.
4. Press the "A" button and hold it down while pressing the "B" button three times.
5. After pressing the "B" button for the third time, the LED will blink rapidly to confirm that the remote control has been reset.

Your BFT remote control should now have been successfully reset. If you still have problems with your remote control, contact a specialized technician for further assistance.

Remember that this reset procedure will erase all previous settings on your BFT remote control. You will need to reprogram it to make it work with your automatic door or gate.

Remote Control Programming

After resetting your BFT remote control, it is necessary to reprogram it to make it work properly with the automation system. Follow these steps:

1. Press and hold down the programming button on the automation until the LED light turns on.

• Release the programming button and immediately press the button on the remote control that you want to program.
• The LED light on the automation control board will flash to confirm that the remote has been programmed correctly.

It is important to note that every time a new remote is added, all previously programmed remotes will be erased from the automation memory. Therefore, if you wish to keep the old remotes, you need to reprogram them along with the new one.

In addition, some BFT automation models require a slightly different procedure for programming the remote. Be sure to consult the user manual specific to your automation model before proceeding with remote programming.

Once remote programming is complete, be sure to test it to verify that it works properly with the automation. If you encounter any problems or difficulties in programming the remote, contact a qualified professional for assistance.

Conclusion

Resetting the BFT remote control may seem like a complicated operation, but by following the correct steps, it can be done in just a few minutes. Remember to carefully follow the instructions in the manual and not skip any steps.

If you have difficulty or doubts, contact a specialized technician who can help you solve the problem.

Remember that resetting the BFT remote control may be necessary in various situations, such as when changing batteries or when connecting it to a new motor. Knowing this procedure will allow you to better manage your home automation system.

• Always keep your BFT remote control user manual handy;
• Follow all the steps indicated in the manual carefully to avoid errors;
• If you encounter difficulties, do not hesitate to seek the help of a qualified professional.

Summary

Resetting the BFT remote control is an important procedure to know in order to better manage your home automation system. It is essential to carefully follow the instructions in the manual and not skip any steps to avoid errors. If you have difficulty, it is always best to seek the help of a specialized technician.

Remember that resetting the BFT remote control may be necessary in various situations, such as when changing batteries or connecting it to a new motor. Always keep your remote control user manual handy and carefully follow all the steps indicated to perform this operation quickly and easily.